Exactly How to Remove and Change a Bathtub
Exactly How to Remove and Change a Bathtub
Blog Article
Do you find yourself trying to locate content about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard job. If the old bathtub is readily easily accessible, the task can move immediately; if you need to open a wall surface to get rid of the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This post will certainly aid you install a new tub in your washroom if you have actually currently bought a new tub as well as do not require to change the arrangement of your previous supply of water pipes.
Your devices and also material checklist ought to make up the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before moving on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bathtub up until the spirit level checks out level.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water supply as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and also the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The former type needs to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles using waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt about Tools You Need to Install a New Bathtub . Thanks for finding the time to read our article. Enjoyed our review? Please share it. Help someone else find it. Thanks a lot for going through it.
Get Quote
Report this page